How to Check Genuine TMT Bars: 4 Key Checks | Amba Shakti
Articles in English

How to Check if a TMT Bar Is Genuine: BIS Mark, Heat Number and Rib Markings

How to Check if a TMT Bar Is Genuine: 4 Key Checks

By Rishika · Last reviewed: 12 November 2026

Short answer: A genuine TMT bar can be traced from the steel in your hand back to a licensed mill. Check four things: the brand and grade rolled into the bar itself, the BIS licence number (CM/L) on the bundle tag and test certificate, a heat number that matches the mill test certificate (MTC), and a weight per metre inside the IS 1786:2008 tolerance. If any one of these is missing or does not match, do not accept the lot.

This guide shows what each marking means, how to verify it in about 15 minutes, which popular “tests” prove nothing, and what to do if a bar fails. Reinforcement bars covered by IS 1786 fall under mandatory BIS certification in India, so an unmarked or untraceable bar is a red flag regardless of price.

The 4-point genuine bar check

  1. Rolled-in markings on the bar. Brand name or trademark and grade, repeated along the length.
  2. BIS Standard Mark and licence number. On the bundle tag and the mill test certificate, verifiable online.
  3. Heat number and traceability. The number on the tag, the bar and the MTC must agree.
  4. Weight and dimensions. Mass per metre within the IS 1786:2008 tolerance, with consistent rib pattern.

1. Rolled-in brand and grade markings

Under the BIS product manual for IS 1786, bars must carry identification marks introduced during rolling, at intervals of not more than 3 metres. These identify the manufacturer’s brand name or trademark and the grade of the bar.

What to look for:

  • Raised characters or symbols that are part of the bar surface, not paint, stickers or ink.
  • The marking repeating along the whole bar, not just at one end.
  • A grade that matches what you ordered, for example Fe 550, Fe 550D or Fe 550 CRS.
  • Sharp, readable characters. Worn, smudged or inconsistent marks suggest re-rolled or counterfeit bars.
Rolled brand and grade marking on an Amba Shakti Fe 550D TMT bar. Caption: Genuine rolled markings are raised on the bar surface and repeat along its length.
Rolled brand and grade marking on an Amba Shakti Fe 550D TMT bar. Caption: Genuine rolled markings are raised on the bar surface and repeat along its length.

 

Suggested alt text: Side-by-side comparison of an Amba Shakti TMT bar with clear rolled brand and Fe 550D grade markings versus an unmarked bar.
Check for clear, readable brand and grade markings on TMT bars. An unclear or missing marking should prompt further verification with the manufacturer before purchase.

“Amba Shakti TMT bars carry the manufacturer’s rolled brand identification, the applicable product grade marking (such as Fe 550D), and other prescribed identification marks on the bar surface.”

2. BIS Standard Mark and CM/L licence number

A BIS-certified manufacturer holds a licence number written as CM/L- followed by digits. The Standard Mark and the licence details should appear on the bundle tag and on the test certificate for each lot.

How to verify:

  1. Note the CM/L number from the bundle tag or the MTC.
  2. Look it up through the BIS Care app or the licence search on the BIS website.
  3. Confirm that the licence belongs to the same manufacturer, covers IS 1786 reinforcement bars and is currently valid.
  4. Compare the manufacturer name and plant on the licence with the name on the tag and the delivery documents.

A licence number that cannot be found, belongs to a different company or has lapsed means the BIS claim is unsupported, whatever the tag says.

For Amba Shakti, see the credentials page for certifications and the quality process for how each batch is tested.

3. Heat number and the mill test certificate

A heat number (also called a cast or melt number) identifies the batch of molten steel a bar came from. IS 1786 requires a tag on every bundle or coil showing the cast or lot number, grade and size, and a test certificate that carries the Standard Mark, cast or lot number, grade, size and test results.

Checking traceability:

  • Read the heat number on the bundle tag.
  • Ask for the MTC for that heat number and diameter.
  • Confirm the heat number, grade and size on the MTC match the tag and the bar.
  • Check the chemical and mechanical values on the MTC against the grade you ordered (yield strength, tensile strength, elongation, carbon equivalent).

Amba Shakti states that each coil and cut length carries a laser-marked heat number traceable to its chemistry report and MTC. See the TMT bars page and the individual product pages for Fe 550 SD, Fe 550D Flexion and Fe 550 CRS Flexion.

TMT bar bundle tag with heat number matching the mill test certificate.
TMT bar bundle tag with heat number matching the mill test certificate.

4. Rib pattern, finish and weight

Deformed bars rely on ribs for bond with concrete. On a bar from an integrated mill, ribs tend to be uniform, evenly spaced and sharp along the whole length. Irregular, shallow or worn ribs, wavy surfaces and uneven diameters are warning signs, because re-rolled or poorly controlled production often shows them.

Then weigh it. Bars that are consistently light give you less steel than the design assumes. Follow our step-by-step method in How to Verify TMT Bar Weight at the Site, and use the TMT bar weight chart to look up the nominal weight for each size. For how sizes differ in use, see 8 mm, 10 mm, 12 mm and 16 mm TMT bars compared.

Genuine vs suspect: quick comparison

Check Genuine bar Warning sign
Brand and grade Raised, repeated along the bar Missing, painted, sticker only, or only at one end
BIS licence (CM/L) On tag and MTC, found and valid in the BIS lookup Not found, expired, or a different company
Heat number Tag, bar and MTC agree No tag, no MTC, or numbers differ
Ribs Uniform, sharp, evenly spaced Irregular, worn or wavy
Weight per metre Within IS 1786:2008 tolerance Consistently below the lower limit
Supplier Authorised dealer or mill, with invoice Unnamed seller, cash-only, price far below market

Tests that do not prove a bar is genuine

  • The magnet test. Almost all carbon steel is magnetic, so this does not separate good bars from bad.
  • Colour or rust. Surface rust or a bluish or dark colour reflects storage and rolling conditions, not compliance.
  • Price alone. A very low price is a warning sign, but a normal price does not prove the bar is genuine.
  • A brand name on the tag only. Tags can be copied. The rolled marking and the MTC are harder to fake.
  • Visual smoothness. A clean-looking bar can still be under grade. Only chemistry and mechanical tests prove grade.

A simple site bend check

A site bend test is a screen, not a replacement for lab testing. Bend a sample around a suitable former to the angle your site engineer specifies, then check the outer surface of the bend. A cracked or peeling outer surface means the bar should not be used. For formal acceptance, rely on the bend and re-bend tests in IS 1786 and on laboratory reports.

What to do if a bar fails

  1. Stop using the lot and tag it clearly.
  2. Photograph the marking, the tag, the delivery challan and the scale readings.
  3. Ask the supplier for the MTC for that heat number and for the BIS licence details.
  4. Send samples to an accredited laboratory if the documents do not settle the question.
  5. Inform the supplier in writing and follow the rejection terms in your purchase order.

Find a genuine Amba Shakti supplier near you

Buy from the manufacturer or an authorised dealer, and keep the invoice, challan and MTC together. Start with Find a dealer, Find Ambashakti near you or the distributor network across India, or contact us directly.

Region Local TMT bar price page Distributors
Delhi NCR Delhi, Faridabad, Gurgaon, Noida, Ghaziabad Distributors in Delhi
Haryana Gurgaon, Faridabad Distributors in Haryana
Uttar Pradesh Uttar Pradesh, Kanpur, Prayagraj, Varanasi Distributors in Uttar Pradesh
Rajasthan Rajasthan, Jaipur, Jodhpur, Udaipur, Bikaner Distributors in Rajasthan
Punjab Punjab Distributors in Punjab
Madhya Pradesh Madhya Pradesh, Bhopal, Indore, Gwalior, Ujjain Distributors in Madhya Pradesh

For current all-India rates, see TMT bar price today.

Frequently asked questions

How can I tell if a TMT bar is BIS certified? Check for rolled-in brand and grade markings on the bar, the Standard Mark and CM/L licence number on the bundle tag and test certificate, then confirm the licence is valid and belongs to that manufacturer through the BIS Care app or BIS website.

What is a heat number on a TMT bar? A heat number identifies the batch of steel the bar was made from. It lets you match the bar to its mill test certificate, which records the chemical and mechanical test results for that batch.

Are rib markings enough to prove a bar is genuine? No. Rolled markings are one of four checks. You also need a verifiable BIS licence, a matching heat number and MTC, and a weight per metre within tolerance.

Does the magnet test show whether TMT steel is genuine? No. Almost all steels used for reinforcement are magnetic, so the test cannot tell good bars from bad ones.

What should I do if my supplier cannot give an MTC? Do not accept the lot until the MTC for that heat number is provided. Ask the manufacturer or an authorised dealer, and use a laboratory test if the documents are still missing.

Keep reading

Marking and licensing requirements are drawn from IS 1786:2008 and the BIS product manual for IS 1786. Standards and BIS rules change; always refer to the current edition and to BIS for licence verification.

Preet Kaur
Written by

Preet Kaur